Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Blog Article
How do you feel in regards to How to Install a Bathtub Yourself?
Mounting a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a moderately hard job. If the old tub is easily available, the job can relocate immediately; if you need to open a wall surface to remove the old tub as well as place the new bath tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will require an assistant to leave the old bathtub as well as set in the new one. See to it you have actually certified on your own for the job and also fit attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is better to consider using one before you start. Possibilities are you might require a professional plumber to make tube connections.
This short article will aid you mount a new bath tub in your bathroom if you have currently gotten a new bathtub as well as do not need to change the arrangement of your previous water system pipelines.
Your devices as well as product checklist ought to make up the following:
Planning for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you should do is separate the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the restricted gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the required setting. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the bathtub up until the level checks out degree.
To install faucets, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the water system as well as check all joints as well as brand-new pipework for leakages and also tighten them if needed. Fill the bathtub and also check the overflow outlet and also the normal outlet for leaks.
Finally, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bath tub needs to wait until the tub has actually been made use of a minimum of when as this will certainly settle it right into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers are in location in between the faucet and also the sink. Secure the tap in position with the producer provided backnut. Once the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind ought to be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to split an inflexible seal, creating the water to pass through the wall between the bathroom as well as the tiling, bring about complications with wetness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealer can crack fairly very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our post about Installing A Bathtub. Thanks a lot for spending some time to browse our content. Are you aware of somebody who is curious about the topic? Take a moment to share it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Schedule A Free Estimate Report this page